Skip to main content

Ripping Vinyl LP Records

Turntable used for ripping vinyl records If you're like me, you have a large collection of vinyl LP records that rarely get played because CDs and MP3 players are so much more convenient. And if you're like me, you want to move all of your audio assets into a more accessible format - your iPod - so that you can finally put that turntable away.

Ripping Vinyl to your iPod

The solution, of course, is to rip your LPs and cassettes. This entails playing each recording, digitizing the music as it plays, and then putting the digitized music into a form that any iPod can use.

My goal during this project was to develop an easy, repeatable, and very high quality process to digitize LPs. This article explains the process.

The Rules of High Quality Vinyl Ripping

Accuracy. On your home hifi system, you look to hear the best sound in your ears. The digitization process is fundamentally different. Digitization is all about capturing the source analog signal as accurately as possible. Do you have a fancy $5000 A/V receiver? Lose it! Such a component will give you no ripping advantage, and very likely will be a quality liability. Digitization is NOT about amplification, it's about accuracy. (after digitization we can put the signal though filters to improve the sound).

Symmetry. When you listening to music, you might like to tweak a couple of settings to suit the room, your listening preference, or to correct an imperfect recording. Don't do it! While digitizing, you want your analog signal to be completely consistent with the analog recording. While you're digitizing, don't move cables or adjust analog settings. Make sure the turntable is well isolated. And avoid power fluctuations that can noise up an otherwise stable analog signal. Don't cook that microwave pizza until you're done, because that noise will very possibly end up in your digitized signal.

Conversion Quality. You don't need the $100 cables, but the cheap bargain-bin cables won't do either. You don't need and shouldn't use speakers - speakers are for listening - and digitization is not listening. And you need a good sound card for quality analog-to-digital conversion (ADC) is critical.

Digitization Equipment and Tools

I started by placing a commodity home amplifier and turntable into the room where my computer resides. Now don't think I went to crazy rearranging all of my equipment - I didn't need speakers or other equipment.

I connected the turntable and receiver into a UPS unit, which also serves as an excellent power conditioner.

The amplifier's role in this project is not the same as it's role while listening to music. During the digitization process, the amp's role is only to act as a pre-amp, feeding the sound card with the milliwatt-level signal sourced from the turntable. Since there is no delivery of sound to the speakers, there is no benefit to using a high wattage amp. In fact, a larger unit will likely just introduce additional noise into the system.

Admittedly I'm a bit of a sound snob, so I did upgrade a few capacitors in the pre-amp section of the amp I used. But most people will get excellent results without getting funky with the circuitry.

Cables

I used generic cables for this set-up. Normally I'd use high quality cables, but given the rapid setup and tear-down of this setup, there was no chance for any oxidization to form between mating surfaces. I love high quality cables for a system that I configure once. But fancy cables are pointless for a one-shot analog digitization system used over the period of a few months.

The Ripping Process
  1. Remove the disc from its dust jacket and check for physical defects. Avoid ripping a damaged disc that will ruin your cartridge.
  2. Clean the record with a quality cleaning tool to minimize noise from dirt. I like the Stanton Record Cleaner Kit. I use a home-made cleaning solution.
  3. Cue up the disc. Start the recording process in Audacity.
  4. As the disc is played, verify the line-in level in Audacity. You want the level to be as high as possible without peaking at 100%. This is highly dependent on the recording and your equipment. In general, the longer the LP in play time, the higher you'll have to set the line-in level.
  5. At the disc run-out, stop the recording process
  6. Save the captured file as a WAV file
  7. Repeat for Side 2.
The same process can work with all forms of audio tape. I have a lot of DBX tape. Same idea, similar process.

Encoding


After you rip, you should convert the files to a lossless compression format for archival. I find that FLAC reduces file size by about 33%. Once I have about 4 GB of FLAC files (about 18 LPs worth of music), I archive the "master" rips onto DVD-R.

My recording program, Audacity, generates WAV files. I then lossless-compress these files into flac form:

flac -V -8 my_album_side_1.wav

This will losslessly convert the WAV file into FLAC at it's best ("-8") compression rate. Flac will verify ("-V") that the resulting file can be converted back into the same exact WAV file. Cool! From there I burn the resulting FLAC files to DVD-R for archival purposes. I find I can put about 18 LPs worth of music on a DVD-R.

I usually don't listen to the FLAC files - they're my "master digitized copy" in case some new music encoding technology comes around the bend.

iPods and other MP3 players

I convert the FLAC files to MP3 format when I want to put them on my iPod. This saves even more space than FLAC, at the expense of sound quality. Since I do most of my iPod listening on the train or in the car, sound quality just isn't that import (too much ambient noise).

Converting the lossless files into MP3 is is also an easy process:
flac -sdc my_album_side_1.flac | lame - my_album_side_2.mp3

Conclusions and Further Thoughts

The digitization process is simple, and can be successfully accomplished using common hardware and freely available software. The important part is to have a consistant, quality digitization so that filters will work appropriately across an entire LP.

In conclusion, converting Vinyl (and other analog recordings) into MP3s should be performed in distinct steps. The distinct steps allow you to have a master lossless copy of the recording in digitized form. After the creation of the master digitized copy, you may apply countless filters and transformations to clean, break apart, or otherwise manipulate the sound. If you need to re-apply transformations, you won't have a need to re-digitize - you'll already have a lossless digital master on hand.

If you'd like more information on the particular hardware and software I use, please drop me a note.

Popular posts from this blog

Fixing a SodaStream Jet, part 1: Disassembly Guide

I've had my SodaStream Jet for years, and once in a while something has gone wrong. Disassembly is the first step to repair.  Start with this article to see how to disassemble the SodaStream, and then once you have that down, scroll through my other articles to see how I repaired specfic SodaStream problems. SodaStream Jet Disassembly Guide Tools Required Flat head screwdriver Phillips head screwdriver 1. Remove the Carbonator.  Duh. 2. Remove the black panel lever The front big black tilt lever needs to be removed first. Removing this panel is tricky, but it isn't impossible. Looking up at the bottom of the black panel, there are two tabs, one on the left and one on the right. These tabs fully secure the panel in place. The trick is to use a flat-head screwdriver under the plastic to gently lever the tabs out of the way.  Note in the pictures how I approach these tabs with my screwdriver.  I usually release the left side first, and then I release the right

Fixing my Wahl 9918 Groomsman Beard and Mustache Trimmer

Not everyone would bother repairing a $25 beard trimmer, but why not fix something for under $5 instead of spending another $25? My  Wahl 9918 Groomsman Beard and Mustache Trimmer  has admirably performed its beauty duty for many years, but the time came when the battery just wasn't holding a charge any more.  Most people would just put the trimmer in the trash and buy a new one, but I figured I could repair my otherwise excellent Wahl and save some money. In fact, even high priced trimmer and rotary shaver brands, like Norelco and Remington, can be easily repaired using a process similar to the one I used to fix my Wahl.  Read on to find out how. I opened up the Wahl by popping off the black plastic faceplate with a tiny flathead screwdriver, which revealed two screws.  By removing the two screws I was able to easily open up the unit, revealing the guts of the device. Backplate off, Revealing the screws The internals are rather simple: a motor, a simple circuit boar

Sodastream Carbonator Leakage, Usage, and Weight

SodaStream 60L "Carbonator" CO2 cylinders have a specific weight when empty, plus about 410 or so grams for the CO2 they should have when they're "full".  A little while ago I went to buy a replacement Carbonator from my local hardware store. The dealer pulled a new Carbonator out of the box and sensed it was lighter than usual.  He put the "light" Carbonator in the "empty" pile and sold me a different one.  At that moment I concluded that it would be smart of me to weigh both new and empty SodaStream carbonators.  Here are the results. Weighing a SodaStream Carbonator - for both Science and Consumer Protection.       The dealer told me that sometimes the carbonators leak after they leave the SodaStream filling facility.  That means there could be an opportunity for customers like me to get ripped off! The SodaStream cylinders I buy claim to have a net product weight of 410 grams - and that means that a full Soda Stream Carbonator shou

Fixing a SodaStream Jet, Repair #2 - Broken Fill Button

My Soda Stream Jet's fill button broke, which means I can not longer carbonate water by pressing the pushbutton. This caused all sorts of grief in my household. Here is how I managed to repair my Jet to give it another 10 years of life (hopefully). First, a look at the button The fill button on the top of the SodaStream is actually a simple lever. Pressing down on the button moves a pin that does the actual work of pressing open the Carbonator's valve. Unfortunately, the axis point is fairly thin and can see a lot of stress. That's where my Soda Stream button cracked. [ I think the usage tip here is "don't over-press the button like a gorilla, it doesn't do anything but put high stress on the button."] Cracked levering point of the button The Pesky Lever Retaining Pin The Fix It was pretty easy for me to replace the button: Take off the back of the Soda Stream and remove the carbonator. Push out the the button lever's steel retaining pin. This takes qu

Adding a Water Flood Sensor to my Vista-20p alarm system

My Honeywell Vista 20p alarm system is fairly comprehensive, but I want one more feature: an alarm that lets me know when my sump pump isn't working properly. Here is how I added one for about $8 in special parts.   I'm afraid of a flood in my finished basement. I'm fortunate - my basement sump pump system is already redundant, with two independent pumps and two outflow pipes. The primary pump kicks in when the water level reaches 6 inches, and if that doesn't work, then the backup pump kicks in when the water level reaches 7 inches.  The backup pump should never kick in unless the primary pump is having a problem pumping.   But there is a problem with this setup: I might never know if my primary pump has failed, leaving me with no redundancy.  I want to be informed when I have one (or god forbid, two) pump failures. My goal is to have my Vista 20p alert me when the sump's water level is ever beyond the point where my primary pump should have kicked in, alerting me

Robust Installation of an HDHomeRun Networked TV Tuner. 64 OTA channels!

I added an HDHomerun (HDHR) over-the-air (OTA) streaming box to my home network, bringing over-the-air broadcast TV to my computers, phones and tablets.  The HDHR is a big upgrade from my previous setup: using a simple "window mount" antenna directly connected to my TV. A TV-attached antenna is good for watching some TV for free, but the HDHR offers so much more flexibility. Figure 0: HDHomeRun on my basement wall   My original OTA TV setup was haphazard at best. It was finicky, ugly, and hard for other people at home to use. I would actually tape my antenna to a window whenever I wanted to watch OTA TV. Plus, it only worked on my TV and not with my other devices. I wanted a cleaner and more modern OTA setup. After looking at possibilities, I developed two goals: (1) bring my OTA TV into the modern Internet-connected era, and (2) set it up in a reliable and pretty way so that other family members wouldn't have to fool around with the antenna or anything else.  With that,

Other Posts

Show more