Skip to main content

The Asus WL500W and DD-WRT


I've been running my ASUS WL-500W Wireless N Router with DD-WRT for a good two months now.

Here's what I've found:

It works great for me!

I hated my WL-500W with the stock firmware. It seemed clunky and didn't behave all that well, despite updated firmware and a plethora of promising features. But since I had this device at my Dad's house, its original shortcomings didn't mean much to me - it worked adequately for him, so I was fine with it.

But a few months ago my Dad received a "free" wireless access point from his new internet service provider, so I ended up with the WL500W. I decided that DD-WRT was the only way to go.

Installation

I installed the Mega Generic, v24 preSP2 (Build13064), available from the DD-WRT web site. I followed these TFTP instructions. Installation was a breeze using TFTP. I was stoked to see it boot.

Issue #1 - making a brick.

I was busily reconfiguring the WL500W soon after it booted: make a config change, save, make another change, save, etc. And then it turned into a brick.

The LEDs on the WL-500W started to flash as if it was in a constant reboot cycle. I became sad; despondent almost. I struggled to use any software technique I could find to unbrick it. After several painstaking hours, I gave up on a "soft solution" to unbricking it.

Unbricking.

After so many wasted hours, I concluded that the only way to unbrick it was with a hardware technique. I went after the brick using the pin 9 grounding unbrick method. I've heard mixed reviews on this technique - some have claimed that this method will permanently damage the device. But since I otherwise had a brick, I decided to take the risk.

In my case, the unbrick method seemed to work wonderfully. Phew! The brick was no more. I reinstalled DD-WRT and did my best to...

...Avoiding Bricking.

I think my mistake was saving configuration changes too quickly. Now, when I make a change to the configuration, I give the WL500W a good long while (like a couple minutes) to commit the change to flash memory. I wait until the load average goes down to near zero before saving another configuration change.

I'm not sure if it really helps, but I haven't bricked the router since I instituted my new "slow save" procedure.

Other issues.

I mistakenly tripped power to the WL500W last week, and it didn't come back up: The "AIR" lamp stayed off, and the device wasn't accessible via ethernet. After experimentation, I found that the device would start up normally if I unplugged my laptop from the WL500W's ethernet port when powering up the WL500W. I didn't look into the "failed boot" condition any further.

The other issue is that I could never get the USB ports on the WL500W to do anything useful for me. Then again, the same was true when I used the stock ASUS firmware.

Performance.

I find that the WL500W performs quite well for a 2.5 GHz-only "N" router. It certainly beats the pants off of many other N-class home routers that I've used.

The WL500W with DD-WRT has been rock solid. I do have it automatically restart weekly, but I have never had any indication that it actually needs to be restarted on a schedule.

And it can easily run with that Mega build. I love having most all of the DD-WRT features on the box. Once you go Mega, it's hard to go back.

Well, I hope that helps!
Labels:

Popular posts from this blog

Fixing a SodaStream Jet, part 1: Disassembly Guide

I've had my SodaStream Jet for years, and once in a while something has gone wrong. Disassembly is the first step to repair.  Start with this article to see how to disassemble the SodaStream, and then once you have that down, scroll through my other articles to see how I repaired specfic SodaStream problems. SodaStream Jet Disassembly Guide Tools Required Flat head screwdriver Phillips head screwdriver 1. Remove the Carbonator.  Duh. 2. Remove the black panel lever The front big black tilt lever needs to be removed first. Removing this panel is tricky, but it isn't impossible. Looking up at the bottom of the black panel, there are two tabs, one on the left and one on the right. These tabs fully secure the panel in place. The trick is to use a flat-head screwdriver under the plastic to gently lever the tabs out of the way.  Note in the pictures how I approach these tabs with my screwdriver.  I usually release the left side first, and then I release the right
Read more

Sodastream Carbonator Leakage, Usage, and Weight

SodaStream 60L "Carbonator" CO2 cylinders have a specific weight when empty, plus about 410 or so grams for the CO2 they should have when they're "full".  A little while ago I went to buy a replacement Carbonator from my local hardware store. The dealer pulled a new Carbonator out of the box and sensed it was lighter than usual.  He put the "light" Carbonator in the "empty" pile and sold me a different one.  At that moment I concluded that it would be smart of me to weigh both new and empty SodaStream carbonators.  Here are the results. Weighing a SodaStream Carbonator - for both Science and Consumer Protection.       The dealer told me that sometimes the carbonators leak after they leave the SodaStream filling facility.  That means there could be an opportunity for customers like me to get ripped off! The SodaStream cylinders I buy claim to have a net product weight of 410 grams - and that means that a full Soda Stream Carbonator shou
Read more

Fixing a SodaStream Jet, Repair #2 - Broken Fill Button

My Soda Stream Jet's fill button broke, which means I can not longer carbonate water by pressing the pushbutton. This caused all sorts of grief in my household. Here is how I managed to repair my Jet to give it another 10 years of life (hopefully). First, a look at the button The fill button on the top of the SodaStream is actually a simple lever. Pressing down on the button moves a pin that does the actual work of pressing open the Carbonator's valve. Unfortunately, the axis point is fairly thin and can see a lot of stress. That's where my Soda Stream button cracked. [ I think the usage tip here is "don't over-press the button like a gorilla, it doesn't do anything but put high stress on the button."] Cracked levering point of the button The Pesky Lever Retaining Pin The Fix It was pretty easy for me to replace the button: Take off the back of the Soda Stream and remove the carbonator. Push out the the button lever's steel retaining pin. This takes qu
Read more

Fixing my Wahl 9918 Groomsman Beard and Mustache Trimmer

Not everyone would bother repairing a $25 beard trimmer, but why not fix something for under $5 instead of spending another $25? My  Wahl 9918 Groomsman Beard and Mustache Trimmer  has admirably performed its beauty duty for many years, but the time came when the battery just wasn't holding a charge any more.  Most people would just put the trimmer in the trash and buy a new one, but I figured I could repair my otherwise excellent Wahl and save some money. In fact, even high priced trimmer and rotary shaver brands, like Norelco and Remington, can be easily repaired using a process similar to the one I used to fix my Wahl.  Read on to find out how. I opened up the Wahl by popping off the black plastic faceplate with a tiny flathead screwdriver, which revealed two screws.  By removing the two screws I was able to easily open up the unit, revealing the guts of the device. Backplate off, Revealing the screws The internals are rather simple: a motor, a simple circuit boar
Read more

MacBook: burnt out magsafe connector repair

My MacBook (A1342 model from 2009-2010) stopped working, thanks to a cheap knockoff magsafe charger. The magsafe connector looked burnt with heat-distorted melted plastic and some black carbon surfaces.  Plugging in the charger resulted in no lights and no action.  My MacBook was dead. First I tried to clean up the connector with some Q-Tips, tooth picks and solvent, but that did little, as seen in this "after" picture (below).   The heat generated by the aftermarket charger permanently deformed and distorted the MacBook's magsafe connector.  Clearly the damage was significant. Burnt Magsafe Connector - Replacement Required! Looking at iFixIt , I determined that it would not be difficult to replace only the magsafe connector with the right tools.  I hoped and prayed that the problem was isolated to the connector assembly and not the logic board. I bought a replacement magsafe connector assembly (available from Amazon) for under $20 and started to replace it by
Read more

Dustbuster Switch Repair

My Dustbuster vacuum - a CHV-1410, gets a lot of use.  We use it several times per day, every day.  It is a workhorse. Sadly, it was becoming unreliable.  It would be fully charged, and I'd hit the switch and maybe it would begin to start and then stop, or it would lurch and stop - or maybe it would do nothing. My CHV-1410 had a broken switch At first I thought it was the battery, but then I found that by carefully wiggling the switch I was sometimes able to get the vacuum to work.  All that on-off action over the years made the switch unreliable. Instead of throwing away an otherwise perfectly good vacuum, I decided to replace the worn switch.  It's an easy and worthwhile repair with the right part. The one special part needed: A specific $5 Switch There seems to be two types of switches used in these, based on the charging mechanism: For the Lithium models (CHV-1410L and similar), I notice that there are only two conductors are attached to the switch: one for &q
Read more

Other Posts

Show more