Skip to main content

MacBook to TV via HDMI for under $25.

I recently bought a new, modern HDTV: a 42 inch, 1080p Panasonic LCD TV. And one of the first things I wanted to do with my new TV was to hook it up to my trusty MacBook. Like many modern TVs, my new TV has a VGA input, so I figured that'd be the right way to hook it up. I got the following stuff together:
I plugged the dongle into the MacBook, and I plugged the VGA cable between the dongle and the TV. Sure enough, my Mac's video image immediately appeared on my TV. I figured with a little fine tuning, I'd get a great 1080p image!

I was wrong.

Attempt #1: MacBook to HDTV via VGA dongle and cable


The major disappointment is that many new TVs, like mine, won't accept a high resolution 1080p-class signal over VGA. Although my MacBook's "Display Preferences" control panel displays a huge range of potential video resolutions, very few of them work adequately (or at all) with my TV.

I wound up setting the TV to 1280 x 768 ... quite a bit less quality than I hoped for.

Lots of resolutions, but only a few combinations work -
and none look as great as an HDTV should
.
Only 1280 x 768 worked adequately.


There are some minor disappointments too. The VGA cable is big, bulky, and inflexible. It looks clunky. And the audio was noisy - evidently the VGA video signal "bleeds" into the audio signal, resulting in an annoying hum at low volumes.

The Better Solution: HDMI. But with a Mac?

I was happy enough with my VGA solution, but I was looking for something better.

The story on the street is that Macs don't do HDMI. That isn't exactly the full story. The truth is that Mac's "do" DVI and DisplayPort, and both can be converted into HDMI.

But Apple doesn't sell DVI to HDMI such converters. I figured the complexity of such a device would result in extremely high costs.

So I did some snooping around. I checked out Amazon and discovered this Mini-DVI to HDMI dongle for under $10! "Too low, it can't possibly work!," I exclaimed. But for such a low price, I figured I'd take a risk and buy one. (For those with a new Mac that uses DisplayPort: you'll likely want a Mini DisplayPort to HDMI Adapter instead.)

The Magic: Mini-DVI to HDMI dongle.

At the same time, I bought an inexpensive HDMI Cable and a 3.5mm Male to RCA audio cable.


MacBook to HDMI: Mini-DVI to HDMI, along with audio cable.

I hooked this stuff together with my MacBook, attaching the new dongle to my Mac, the HDMI cable between my Mac and my TV, and the audio cable between the headphone port on my Mac and my TV.

The result? Stunning!

In fact, with the HDMI converter, my Mac can recognize both my TV's manufacturer and its supported video modes. Recall that with the VGA solution, my Mac just showed me a heap of possible settings, some good, many not good.

With the inexpensive HDMI Adapter, my Mac detects
the TV and the mode it supports

I could have improved my audio by adding a TOSLink digital optical audio cable, but since I don't have a modern audio system (another story!), I decided to hold onto my money.

Final Notes

If you have a Mac that you want to connect to a modern TV, HDMI is a great way to go. The cabling is flexible and inexpensive, and the quality is high.

Popular posts from this blog

Fixing a SodaStream Jet, part 1: Disassembly Guide

I've had my SodaStream Jet for years, and once in a while something has gone wrong. Disassembly is the first step to repair.  Start with this article to see how to disassemble the SodaStream, and then once you have that down, scroll through my other articles to see how I repaired specfic SodaStream problems. SodaStream Jet Disassembly Guide Tools Required Flat head screwdriver Phillips head screwdriver 1. Remove the Carbonator.  Duh. 2. Remove the black panel lever The front big black tilt lever needs to be removed first. Removing this panel is tricky, but it isn't impossible. Looking up at the bottom of the black panel, there are two tabs, one on the left and one on the right. These tabs fully secure the panel in place. The trick is to use a flat-head screwdriver under the plastic to gently lever the tabs out of the way.  Note in the pictures how I approach these tabs with my screwdriver.  I usually release the left side first, and then I release the right

Fixing a SodaStream Jet, Repair #2 - Broken Fill Button

My Soda Stream Jet's fill button broke, which means I can not longer carbonate water by pressing the pushbutton. This caused all sorts of grief in my household. Here is how I managed to repair my Jet to give it another 10 years of life (hopefully). First, a look at the button The fill button on the top of the SodaStream is actually a simple lever. Pressing down on the button moves a pin that does the actual work of pressing open the Carbonator's valve. Unfortunately, the axis point is fairly thin and can see a lot of stress. That's where my Soda Stream button cracked. [ I think the usage tip here is "don't over-press the button like a gorilla, it doesn't do anything but put high stress on the button."] Cracked levering point of the button The Pesky Lever Retaining Pin The Fix It was pretty easy for me to replace the button: Take off the back of the Soda Stream and remove the carbonator. Push out the the button lever's steel retaining pin. This takes qu

Sodastream Carbonator Leakage, Usage, and Weight

SodaStream 60L "Carbonator" CO2 cylinders have a specific weight when empty, plus about 410 or so grams for the CO2 they should have when they're "full".  A little while ago I went to buy a replacement Carbonator from my local hardware store. The dealer pulled a new Carbonator out of the box and sensed it was lighter than usual.  He put the "light" Carbonator in the "empty" pile and sold me a different one.  At that moment I concluded that it would be smart of me to weigh both new and empty SodaStream carbonators.  Here are the results. Weighing a SodaStream Carbonator - for both Science and Consumer Protection.       The dealer told me that sometimes the carbonators leak after they leave the SodaStream filling facility.  That means there could be an opportunity for customers like me to get ripped off! The SodaStream cylinders I buy claim to have a net product weight of 410 grams - and that means that a full Soda Stream Carbonator shou

Fixing my Wahl 9918 Groomsman Beard and Mustache Trimmer

Not everyone would bother repairing a $25 beard trimmer, but why not fix something for under $5 instead of spending another $25? My  Wahl 9918 Groomsman Beard and Mustache Trimmer  has admirably performed its beauty duty for many years, but the time came when the battery just wasn't holding a charge any more.  Most people would just put the trimmer in the trash and buy a new one, but I figured I could repair my otherwise excellent Wahl and save some money. In fact, even high priced trimmer and rotary shaver brands, like Norelco and Remington, can be easily repaired using a process similar to the one I used to fix my Wahl.  Read on to find out how. I opened up the Wahl by popping off the black plastic faceplate with a tiny flathead screwdriver, which revealed two screws.  By removing the two screws I was able to easily open up the unit, revealing the guts of the device. Backplate off, Revealing the screws The internals are rather simple: a motor, a simple circuit boar

Adding a Water Flood Sensor to my Vista-20p alarm system

My Honeywell Vista 20p alarm system is fairly comprehensive, but I want one more feature: an alarm that lets me know when my sump pump isn't working properly. Here is how I added one for about $8 in special parts.   I'm afraid of a flood in my finished basement. I'm fortunate - my basement sump pump system is already redundant, with two independent pumps and two outflow pipes. The primary pump kicks in when the water level reaches 6 inches, and if that doesn't work, then the backup pump kicks in when the water level reaches 7 inches.  The backup pump should never kick in unless the primary pump is having a problem pumping.   But there is a problem with this setup: I might never know if my primary pump has failed, leaving me with no redundancy.  I want to be informed when I have one (or god forbid, two) pump failures. My goal is to have my Vista 20p alert me when the sump's water level is ever beyond the point where my primary pump should have kicked in, alerting me

Robust Installation of an HDHomeRun Networked TV Tuner. 64 OTA channels!

I added an HDHomerun (HDHR) over-the-air (OTA) streaming box to my home network, bringing over-the-air broadcast TV to my computers, phones and tablets.  The HDHR is a big upgrade from my previous setup: using a simple "window mount" antenna directly connected to my TV. A TV-attached antenna is good for watching some TV for free, but the HDHR offers so much more flexibility. Figure 0: HDHomeRun on my basement wall   My original OTA TV setup was haphazard at best. It was finicky, ugly, and hard for other people at home to use. I would actually tape my antenna to a window whenever I wanted to watch OTA TV. Plus, it only worked on my TV and not with my other devices. I wanted a cleaner and more modern OTA setup. After looking at possibilities, I developed two goals: (1) bring my OTA TV into the modern Internet-connected era, and (2) set it up in a reliable and pretty way so that other family members wouldn't have to fool around with the antenna or anything else.  With that,

Other Posts

Show more