Leaving Sprint for Huge Cost Savings

So my friend is under a Sprint contract, and it's killing him. He pays $145 a month for service for two lines, and he has 8 months left on his contract. That is $1745 a year!

He came to me because he wanted to upgrade his phones - he has two iPhone 5c's with 8 GB of storage - not enough - and so he was thinking of signing up with Sprint for another two years to get "new phones". Stop! Stop the contracts! $1745 a year is a LOT OF MONEY.

So we have THREE problems:

He is under contract for 8 more months, at $145 a month.
He has two phones that are too limiting for his day-to-day use
He has two phones that are locked to the Sprint network

We have FOUR goals:

Reduce money being sucked out the door
Get phones that are not so limiting
Get phones that are not locked exclusively to Sprint
Get out of any "contracts"

Stage 1: New phones!

So our first step is to get new phones - phones that will work with Sprint or any other carrier.

Well, not NEW phones, but good and affordable USED phones. We are ordering a couple unlocked 32 GB iPhone 5Cs. They're pretty inexpensive, at $140.

Then we hope to sell the 8 GB iPhone 5Cs for about $100. That's an $80 expense in total, if it all goes our way.

Stage 2: Validating the new phones

Stay tuned! We haven't received the "better" phones yet.

Fixing a SodaStream Jet, part 1: Disassembly Guide

I've had my SodaStream Jet for years, and once in a while something has gone wrong. Disassembly is the first step to repair. Start with this article to see how to disassemble the SodaStream, and then once you have that down, scroll through my other articles to see how I repaired specfic SodaStream problems. SodaStream Jet Disassembly Guide Tools Required Flat head screwdriver Phillips head screwdriver 1. Remove the Carbonator. Duh. 2. Remove the black panel lever The front big black tilt lever needs to be removed first. Removing this panel is tricky, but it isn't impossible. Looking up at the bottom of the black panel, there are two tabs, one on the left and one on the right. These tabs fully secure the panel in place. The trick is to use a flat-head screwdriver under the plastic to gently lever the tabs out of the way. Note in the pictures how I approach these tabs with my screwdriver. I usually release the left side first, and then I release the right

Sodastream Carbonator Leakage, Usage, and Weight

SodaStream 60L "Carbonator" CO2 cylinders have a specific weight when empty, plus about 410 or so grams for the CO2 they should have when they're "full". A little while ago I went to buy a replacement Carbonator from my local hardware store. The dealer pulled a new Carbonator out of the box and sensed it was lighter than usual. He put the "light" Carbonator in the "empty" pile and sold me a different one. At that moment I concluded that it would be smart of me to weigh both new and empty SodaStream carbonators. Here are the results. Weighing a SodaStream Carbonator - for both Science and Consumer Protection. The dealer told me that sometimes the carbonators leak after they leave the SodaStream filling facility. That means there could be an opportunity for customers like me to get ripped off! The SodaStream cylinders I buy claim to have a net product weight of 410 grams - and that means that a full Soda Stream Carbonator shou

Fixing a SodaStream Jet, Repair #2 - Broken Fill Button

My Soda Stream Jet's fill button broke, which means I can not longer carbonate water by pressing the pushbutton. This caused all sorts of grief in my household. Here is how I managed to repair my Jet to give it another 10 years of life (hopefully). First, a look at the button The fill button on the top of the SodaStream is actually a simple lever. Pressing down on the button moves a pin that does the actual work of pressing open the Carbonator's valve. Unfortunately, the axis point is fairly thin and can see a lot of stress. That's where my Soda Stream button cracked. [ I think the usage tip here is "don't over-press the button like a gorilla, it doesn't do anything but put high stress on the button."] Cracked levering point of the button The Pesky Lever Retaining Pin The Fix It was pretty easy for me to replace the button: Take off the back of the Soda Stream and remove the carbonator. Push out the the button lever's steel retaining pin. This takes qu

Fixing my Wahl 9918 Groomsman Beard and Mustache Trimmer

Not everyone would bother repairing a $25 beard trimmer, but why not fix something for under $5 instead of spending another $25? My Wahl 9918 Groomsman Beard and Mustache Trimmer has admirably performed its beauty duty for many years, but the time came when the battery just wasn't holding a charge any more. Most people would just put the trimmer in the trash and buy a new one, but I figured I could repair my otherwise excellent Wahl and save some money. In fact, even high priced trimmer and rotary shaver brands, like Norelco and Remington, can be easily repaired using a process similar to the one I used to fix my Wahl. Read on to find out how. I opened up the Wahl by popping off the black plastic faceplate with a tiny flathead screwdriver, which revealed two screws. By removing the two screws I was able to easily open up the unit, revealing the guts of the device. Backplate off, Revealing the screws The internals are rather simple: a motor, a simple circuit boar

MacBook: burnt out magsafe connector repair

My MacBook (A1342 model from 2009-2010) stopped working, thanks to a cheap knockoff magsafe charger. The magsafe connector looked burnt with heat-distorted melted plastic and some black carbon surfaces. Plugging in the charger resulted in no lights and no action. My MacBook was dead. First I tried to clean up the connector with some Q-Tips, tooth picks and solvent, but that did little, as seen in this "after" picture (below). The heat generated by the aftermarket charger permanently deformed and distorted the MacBook's magsafe connector. Clearly the damage was significant. Burnt Magsafe Connector - Replacement Required! Looking at iFixIt , I determined that it would not be difficult to replace only the magsafe connector with the right tools. I hoped and prayed that the problem was isolated to the connector assembly and not the logic board. I bought a replacement magsafe connector assembly (available from Amazon) for under $20 and started to replace it by

Dustbuster Switch Repair

My Dustbuster vacuum - a CHV-1410, gets a lot of use. We use it several times per day, every day. It is a workhorse. Sadly, it was becoming unreliable. It would be fully charged, and I'd hit the switch and maybe it would begin to start and then stop, or it would lurch and stop - or maybe it would do nothing. My CHV-1410 had a broken switch At first I thought it was the battery, but then I found that by carefully wiggling the switch I was sometimes able to get the vacuum to work. All that on-off action over the years made the switch unreliable. Instead of throwing away an otherwise perfectly good vacuum, I decided to replace the worn switch. It's an easy and worthwhile repair with the right part. The one special part needed: A specific $5 Switch There seems to be two types of switches used in these, based on the charging mechanism: For the Lithium models (CHV-1410L and similar), I notice that there are only two conductors are attached to the switch: one for &q

The Lance J. Technoweb

Search This Blog